Remote Load Drop Hook

The Dropper 10 is a 10 Tonne automatic load drop hook that allows you to drop any load safely and at a distance with the use of the remote control.
No need to climb, use of ropes or cables to drop the load. Release the load effortlessly. from a safe distance.

Experience the convenience of our quick drop system, making your workflow seamless and secure

See the Remote Load Drop Hook in action

 

How does it Work?

Set-up for a safe drop:

*A drop hook can produce deaths and a lot of damage. Therefore we included  some features to make this probability as close to zero as possible.

  1. Ensure safety pin is in the top slot. Confirm the hook is open and LEDs display green.
  2. Manually close the hook
  3. Extract safety key pin from top slot
  4. Insert the safety key pin into the bottom slot. Turn the safety key pin 90 degrees right (clockwise) to activate autoclose sensor.
  5. Autoclose sensor orders the safety latch to lock, turning LEDs from green to red. Transition time is about 15 seconds. Do not attempt to move or extract the pin while is in red.
  6.  Procedure ends when LEDs change to blue. Now hook is closed and secured with the pin.
  7. Connect the load using the provided shackle. The pin is securing the load. So even if the order is given it can not drop the load yet.
  8. Move the safety pin from the bottom  to the top slot and turn it 90 degrees. Now it is ready to drop the load.

Before lifting the load, make sure everyone is at a safe distance. The hazard area should be fenced and people must stay out of the area. 

Once the Dropper is set up, and hazar area is clear, load can be lifted to the desired drop height.

Safe Drop procedure:

The HookBot operates through activation involving dual verification with two Emini commands. This is to ensure the safe release of the load and prevent errors.

More Info
After successfully setting up the quick release system following the specified procedure, Dropper 10 is now equipped for efficient drop and hook loads with its automatic unloading feature, ensuring a seamless transition from load attachment to load release

 

Dropper

In Detail

10 Tonne Load Drop Hook
The Minimum Releasable Weight is 20 kgs/44 lbs.*

(For lower values, please contact the sales department.)

High-Brightness LED
Status Indicator

The color of the LEDs indicates the state of the hook.

Green: Dropper is Open / Unlocked
Red: Transitioning: Do Not Lift!
Blue: Dropper is Closed / locked
White: Low Battery

LEDs for Automatic Load Drop Hook

Trust in our load release hook to deliver a secure and efficient operation every time. This seamless process ensures efficient and secure drop loads with the quick release system

Load Cell

(Coming soon)

The Dropper can be equipped with a load cell for precise load measurements during the lifting process.

Our load cells provide quick and accurate readings, offering affordability and a longer lifespan compared to other sensors. Primarily used for weighing and preventing overloads, the load cell, when combined with the remote control, transforms the automatic load drop hook into a sophisticated and precise weighing scale with advanced features.

Elevate your operations with our innovative load release hook.

 

Load Cell for Automatic Load Drop Hook

More Info about the Load Cell

Specifications

Nominal Load (Ln) 10t
Accuracy Class 0.5%
Minimum dead load 0% Ln
Service load 150% Ln
Ultimate load limit >400% Ln
Total error < ±0.5 % Ln
Repeatability error < ±0.2% Ln
Temperature effect on zero  < ±0.2% Ln/ 5ºC
Temperature effect on sensitivity  < ±0.2% Ln/ 5ºC
Creep error (30 min) < ±0.1% Sn
Temperature compensation -20 to +60 ºC
Storage temperature – 40 to +95ºC
Service temperature limits  -20 to +90 ºC
Excitation voltage 3…15 V
Imput impedance 400 ±30 Ohm
Environmental Protection IP66
Material Stainless steel
Cable gland + Shielded cable 4 wires 5M

High-Capacity Battery

With the high-capacity battery, a simple 3 hour charge allows for
more than 3.000 cycles or over 250 hours in standby mode.

The battery remains protected from accidental impacts as the slot cover is protected
with a safety lock which protects the battery from falling in case of impact.

Automatic Load Drop Hook Battery

 

Dual Remote Controlled Release

The Dropper is to be used with dual remote control.

Automatic Load Drop Hook Remote Control

We decided to use a dual remote control. By using 2 remotes this is reduced enven more.

Both remotes work in different frequencies, so it would make it harder for a hacker to sniff it and find the correct one.

By mistake it is very difficult to send the order, as a sequence of buttons have to be pressed on each remote, in a specific order in a defined  time frame.

We advice 2 separate workers to operate each of the remotes.

Shackle

The Dropper 10 is supplied with a shackle. The Green Pin® Bow Shackle BN is a bow shackle with a safety bolt. The shackle offers a double safety (split pin and safety bolt) which prevents accidental unscrewing of the pin.

Material bow and pin high tensile steel, Grade 6, quenched and tempered
Safety Factor MBL equals 6 x WLL
Finish hot dipped galvanized
Temp. Range -40°C up to +200°C
Diameter Pin 35mm. / 1.37in.
Certification 2.1 / 2.2 / 3.1 / MTCa / ABS PDA / ABS MA /
DNV 2.7-1a / DNV 2.7-1b / DNVGL-ST-0378 / CE
Standard N 13889 and meets performance requirements of
US Fed. Spec. RR-C-271, Type IVA, Class 3, Grade A.
From 2 t and upward these shackles comply with ASME B30.26
elebia Dropper

Regulatory Standards Automatic Load Drop Hook Regulatory Standards

The Dropper 10 certifies with the following regulatory standards:

EN ISO12100:2012 EN 61000-6-4:2002
EN 61000-6-2:2002 EN 60204-1:2007

Directive on Machine Safety (D2006/42/EC).

EMC Directive (2014/30/EU).

Low Voltage Directive (2014/35/EU).

Radio Equipment Directive (2014/53/EU).

Assurance of Production Quality in accordance with ISO9001.

ARIB Construction Design Certification Number 203-JN0689.

FCC Identifier 2ACLHEVO for Equipment Class: Digital Transmission System.

Each mechanism is delivered with the CE stamp and a declaration of CE conformity.

elebia is a member of F.E.M. (European Federation of Materials Handling).

 

elebia Dropper

Quick Links

 

Configurator

Personalize and configure
your Dropper 10 remote
load drop hook.

Configure Dropper 10

Schedule a Demo

Colour-Codes-Industrial-Safety-

See in person how your company
can benefit by using the
Dropper 10 load drop hook.

Schedule a Demo

User Manual

All the info you need and
more, of the Dropper 10
remote Load Drop Hook.

User Manual

Quotation

Receive a quote for your
Dropper 10 Load Drop Hook or
any other product and accessory.

Quotation

 

Contact Us

Elebia Autohooks S.L.U.

Plaça Pere Llauger Prim, Naus 10-11

Polígon Industrial Can Misser

08360 Canet de Mar

(Barcelona) Spain

(+34) 93 543 4706

    Enter your full name

    Enter a valid email

    Enter your phone

    Please, insert your company

    Please, select the country where you from

    Select an option

    Enter a brief message